Swap.........avi?
-
weshole;206632 wrote:
A lil off topic (imagine that).... But Parker, what rear diff are you running in the 7?
im using the stock one till the kinks are worked out of it... but by mid summer i will have a ford 8.8 in it... then comes a trans brake and some giggle juice
-
weshole;206639 wrote:
Joel I do belive your wrong about the LSx swap. Those engines are nearly the same weight as the 1.6 in there. You loose nearly none of the cars handling capabilities. They are just an expensive and involved swap to do properly. So it's not for the faint of heart.I never said anything about how much the motor weighs, wes. The fact is, the miata is a quick, Nimble car. I guess 300 ft/lbs of torque doesn't strike me as nimble. With a turbo setup, you aren't always in boost, there for you can still take a corner at a decent amount of throttle without killing yourself. I guess I might just be a n00b driver but thats the way I see it. I would love to have the power of a v8 without having to go forced induction, I don't have the knowledge or the deep pockets needed for doing it properly. I guess my car won't be a monster miata...
-
A quick car? The MIATA? I think not. It IS a fun spirited car to drive because it is so light. But 300 ft lbs as you refer to it is only 300 ft lbs when you decide to use it. I'd rather have the option of having the power and deciding NOT to use than watching whomever go right by. I'm speaking from having one for almost 4 years now. You'll see when you get more wheel time. OF course you may be comparing it to previous cars you have owned. Then it may seem like a supercar. You can only justify the cars handling prowess and power to weight ratio so much.
-
If you ask any Ford gearhead about swapping a 5.0 into a 2.3 foxbody, they'll tell you the cheapest and best way to do is to plain trade in the 2.3 and buy a stock 5.0.
The Ford K-member was designed to accept both the 2.3 mounts and the 5.0 mounts.... if you get a k-member just for swapping the 5.0 into the miata you'll probly run into some major issues with getting the 2.3 mounted. The wireharnesses between a 2.3 and 5.0 are completely different, to the point that some of the pin-outs are different. The fuel line connections are on opposite sides of the engine.
The Monster Miata kit isn't gonna be much help for this one. You'll still find that you need a lot of custom work and that the usual kits aren't going to help much at all
...and don't even get me started on if your donor car had a TFI ignition system.. even the Ford guys are ashamed of that one (especially if the resistor gel overheated, leaked and started the module on fire). :eek: I know you would use the miata ignition, but who knows what issues you might run into with spark plugs and grounds and general wiring, the TFI had super-high risistance on one end in the modules and super-low resistance on the other end to cope with it.
I didn't know there were kits for dropping a 5.0 into a miata.. that swap is kind of frightening.. kewl though :woot:
-
And a Thunderbird 8.8 IRS is a pretty rock-solid rearend, and one of the reasons that a thunderbird can handle just as well as mustang of the same year, despite the car being 500lbs heavier
-
A 2.3 turbo would be a good motor for a Miata and the swap can't be any more difficult than stuffing an LSx into an FD, and a lot of fools have done that one. Just an fyi, for a donor motor getting one from a 82-88 thunderbird turbocoupe or a cougar XR7 would probibly be a lot cheaper than the SVO.
> Mitch Hedberg wrote:
> I'm sick of following my dreams, I'm just going to find out where they are going and hook up with them later.ASE certified parts specialist.
2004 Impala LS 3.8 -
weshole;206652 wrote:
You're not gonna kill the 8.8 IRS out of the Thunderbird. They hold up tp the best that the best LS1-2 throws at it. And...... IT HANDLES with it.
theres a kit for the solid axle... bolts in, nuff said... if someone made a complete kit for the IRS 8.8 i would buy that.... but theres not... so im not going to fuck with it.... the car will handle just fine with a solid axle in it... -
LupusSingularis;206678 wrote:
If you ask any Ford gearhead about swapping a 5.0 into a 2.3 foxbody, they'll tell you the cheapest and best way to do is to plain trade in the 2.3 and buy a stock 5.0.The Ford K-member was designed to accept both the 2.3 mounts and the 5.0 mounts.... if you get a k-member just for swapping the 5.0 into the miata you'll probly run into some major issues with getting the 2.3 mounted. The wireharnesses between a 2.3 and 5.0 are completely different, to the point that some of the pin-outs are different. The fuel line connections are on opposite sides of the engine.
The Monster Miata kit isn't gonna be much help for this one. You'll still find that you need a lot of custom work and that the usual kits aren't going to help much at all
...and don't even get me started on if your donor car had a TFI ignition system.. even the Ford guys are ashamed of that one (especially if the resistor gel overheated, leaked and started the module on fire). :eek: I know you would use the miata ignition, but who knows what issues you might run into with spark plugs and grounds and general wiring, the TFI had super-high risistance on one end in the modules and super-low resistance on the other end to cope with it.
I didn't know there were kits for dropping a 5.0 into a miata.. that swap is kind of frightening.. kewl though :woot:everything you have said is to be expected with this kind of swap...its not hard, it just takes time and research.... lots of it
-
this kind of swap...its not hard, it just takes time and research
and money, just saying he might be better off with something a little more plug-and-play, if working on a budget. If money were no object you could do a turbine engine swap.
my view on the matter is that if it costs more to do the swap than to just buy the car, then why bother, unless you just wanna show off that you have money to spend on odd projects. I dont think the 2.3 project is going to be any cheaper than the Monster Miata kit in the end.
-
LupusSingularis;206678 wrote:
The fuel line connections are on opposite sides of the engine.Fuck that no way, that will never work
LupusSingularis;206678 wrote:
the TFI had super-high risistanceFuck that, it had remote inductance
LupusSingularis;206678 wrote:
issues you might run into with spark plugsIt doesnt even have spark plugs... jeez
LupusSingularis;206678 wrote:
The Ford K-member was designed ... :Its called a F-U member..... dumbass
-
LupusSingularis;206707 wrote:
and money, just saying he might be better off with something a little more plug-and-play, if working on a budget. If money were no object you could do a turbine engine swap.my view on the matter is that if it costs more to do the swap than to just buy the car, then why bother, unless you just wanna show off that you have money to spend on odd projects. I dont think the 2.3 project is going to be any cheaper than the Monster Miata kit in the end.
i guess i just like to show off then... ill just sell it and do what everyone else does.... buy a honda... modding cars costs money.... if you want to "go fast" your gunna have to pay up no matter what you do.... it all depends if you want to be a leader or a follower.... you must be a follower.... -
weshole;206732 wrote:
There's someone that has makes the kit. I'll try to find it and pm ya the info. You can also swap in the 3rd gen diff assy that is VERY strong as well and rather easy to come by. I was gonna do that waaay back when I had a 2nd gen.
i know people that make cradles for the IRS, but i dont want to go through all of the hassel of finding the rest of the shit.... im not interested in swapping a stock 3g rx7 diff in either... by the time this thing hits the spray, it will be around 800hp/trq... and then if the car holds together like it should soon will come some type of FI... plans of around 1000+hp
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login