Welcome sickest honda builder of our time
-
weshole;296449 wrote:
Tell him what you want done and it will get done. Its not rocket science bro. Theres no voodoo trickery slight of hand to sleeving a block. If you know what you are doing, your golden. Same goes for o-ringing a block.damn, i'll keep that in mind
Bassplayer;296455 wrote:
Why would you want to put money into an H22?this
DelSlow;296457 wrote:
A) I don't, just recall a friend of mine trying to get some work done on one and no one will touch them and B) Why not? What's bad about them?**everyone else, let him answer.
I think i might know this one....
-
DelSlow;296457 wrote:
A) I don't, just recall a friend of mine trying to get some work done on one and no one will touch them and B) Why not? What's bad about them?**everyone else, let him answer.
H22 are heavier(only slightly), aftermarket support is waaayyy less and so parts are more expensive, H's tend to be harder to swap depending on the chassis, why have barely any of the respectable honda tuning companies put H22's in their race cars..... I guess the list goes on, I've just never really been a fan. I'm a big supporter of keeping things simple and cheap.
-
Bassplayer;296475 wrote:
H22 are heavier(only slightly), aftermarket support is waaayyy less and so parts are more expensive, H's tend to be harder to swap depending on the chassis, why have barely any of the respectable honda tuning companies put H22's in their race cars..... I guess the list goes on, I've just never really been a fan. I'm a big supporter of keeping things simple and cheap.i think ur wayyy off from what he was thinking still...
I'm thinking he's referring to the use of FRM cylinder walls from the factory...
-
bubba;296478 wrote:
i think ur wayyy off from what he was thinking still...I'm thinking he's referring to the use of FRM cylinder walls from the factory...
Ah thats right, aren't those really weak from the factory and require special sleeves or something?
-
ihaveaids;296479 wrote:
Ah thats right, aren't those really weak from the factory and require special sleeves or something?Well the fact that you can't run aftermarket pistons with them is a bit of a downfall. They are reasonably strong stock, but if you want to run forged internals, you need to resleeve it.
They are a decent motor because they are pretty cheap, and can make decent power, but Im not a supporter either.
And Wes, Sleeves actually do require a very good machinist that knows what they are doing and has a lot of experience (not that it is impossibly hard, but it is a LOT more than boring a block, milling a head, or even o-ringing). I have seen blocks from the big name companies that have had serious issues, fortunately these have pretty much all been figured out over the years, or those companies are no longer around, but I would definately not trust my block to just any machine shop that says they can do it, much better off sending it to a company that does it every day.
-
inspector01;296482 wrote:
I have seen blocks from the big name companies that have had serious issues, fortunately these have pretty much all been figured out over the years, or those companies are no longer around, but I would definately not trust my block to just any machine shop that says they can do it, much better off sending it to a company that does it every day.QFT. As soon as you start the motor up and get some boost on it if anything blows up no motor shop around here is going to take liability for it. Get it done at a place that is known for their sleeving and can back up their work. /thead
-
DelSlow;296437 wrote:
Forgot to throw in $7,000 motor.man i dont want peeps be hatin on my whip knowing all dat dough i throw unda tat hood ill race right by em poundin tat mad v-tec yos dem day no whats up..
1999 civic ex - 472whp 19psi e85
2000 civic SiR - jdm sickness
1988 chevy s10 blazer - lowrider
1979 lifted fullsize chevy - mud truck -
99civic;296493 wrote:
man i dont want peeps be hatin on my whip knowing all dat dough i throw unda tat hood ill race right by em poundin tat mad v-tec yos dem day no whats up..so werd
here a psht, there psht, everywhere a psht psht
PVC SQUAD MEMBER #2- 95 CIVIC EX- DD 320whp on a mustang dyno
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login