For the DSM people.

[GraveDigger]

Haha. Everyone. The percentage of people who don't drive a 4g63 powered car (or some variant of Impreza) are pretty slim.

[pin]

There is an equal number of Hondas/Acuras, plus a number of domestics that have shown up at Sam's Club.

[92TSIpos]

I have a 92 talon tsi (6 bolt 4 bolt)
I had a 16g on my old car and i think its not worth the money
I just spent 750 bucks on my transmission and it shifts like a dream
I love my setup with the stock turbo.

[Guest]

What 16g did you have?

[Guest]

GraveDigger wrote:
Haha. Everyone. The percentage of people who don't drive a 4g63 powered car (or some variant of Impreza) are pretty slim.

I hope you aren't insinuating that the 4g63 is used in an Impreza based car from Subaru but rather that this site is heavily populated by BOTH 4g63 DSM's and Subarus w/ boxer motors.

[TsiTom]

1. My name is Tom, and yes I own a dsm
2. I have a 16g on my car right now, I like it, but I think id be happier with a 50 trim
3. Tranny is doing pretty good...3rd gear is a little grindy when going in at high rpm's
4. I dont know much about the rear-ends but I have a 4 bolt
5. exhaust manifold (1g's) and crank pulley are the only things I can think about off the top of my head...im sure the other dsm owners will add to this list

[aliengotpsi]

Stock 3 bolt Rear End went 11.2 a few times, befor switching to a 4 bolt... O btw I did break many many axles. Have fun and get a 2nd job.. lol

[24valvenotak]

i dont own a dsm but from personal experience...go AT LEAST a step larger then you think you want at the moment..it will pay off next summer

[PSiedTSi]

i know of a 4bolt(or did) for $350 if you are looking to get one...and i honestly wish i woulda gone bigger but it woulda been pointless without an intake manifold and cams which im sure youve heard me say...and you know my setup i believe

[Guest]

I think going with a 50 trim would be too big of a step right now. There are more parts that I would need in order to run a 50 trim over the 16g. I will probably end up going to a 50 trim after this summer is over but it will be a slow progression because of the additional parts that are needed.

I think that my rear-end should be fine because I don't think I will get even close to 11.2 pass at the track. The only thing really holding back my car that is major right now is that damned transmission.

Thanks for the help guys.

Another question I think you could answer it for me Kevin. If I buy one of SLS's manifolds for my 16g could I re-use it once I get my 50 trim?

[weshole]

Yup.

[amicheze]

1. 93 tsi
2. stock 14b
3. not so great. grinds into every gear.. hard time shifting into 2nd without a little working/forcing in.
4. stock 3 bolt
5. my transfer case was fixed under a recall. so far ive gotten a new battery, o2 sensor, and plug wires.

99% of dsms on this board > mine.

[Wizard]

1. 91 RS FWD Auto
2. Ported 14b w/external
3. Auto....what can I say...no missed shifts. And no need to lift.
4. Stock solid rear with crossbar. Adding a rear sway next week.
5. Hard pipes, MBC, 3" Turbo-back out the side, K&N, free mods, pics soon

Bad93EX: Hate to tell you but 3-bolts are known to start breaking with low-12 to high 11-sec cars. Which a 14b is more than capable of. Comes down to clutch and launching softly.

Wiz

[Jim]

Bad93ex wrote:
I think going with a 50 trim would be too big of a step right now. There are more parts that I would need in order to run a 50 trim over the 16g. I will probably end up going to a 50 trim after this summer is over but it will be a slow progression because of the additional parts that are needed.

I think that my rear-end should be fine because I don't think I will get even close to 11.2 pass at the track. The only thing really holding back my car that is major right now is that damned transmission.

Thanks for the help guys.

Another question I think you could answer it for me Kevin. If I buy one of SLS's manifolds for my 16g could I re-use it once I get my 50 trim?

The 50 trim is the new Big 16g. Spoolup isn't drastic, power is great. Good street turbo.

You can use your stock manifold, just get it ported. If your going with a tubular manifold, check out straight garett turbos and have a manifold flanged for t3/t4 (instead of a mitsu hybrid).

The parts needed for a big16 are almost the same as a 50... you'd need:

Injectors
Fuel Pump
Fuel Control (AFC)
Front Mount and Piping
Blow Off Valve

50 you need oil line kit...

I'm trying to think if there is anything else.... maybe a fuel pressure regulator

[Jim]

I own a DSM

Yes, I have a Bullseye Power 50 Trim

It's been rebuilt

[Guest]

I have a DSM....Yes, Its broken.

[treimche]

1. I have a 97 GSX.

2. I run a large Forced Performance turbo, the FP3065

3. Current transmission is great, it's as far from stock as you can possibly get, so my info isn't much good for your situation.

4. You can run the 3 bolt rear end for quite a while as long as you're careful with it. When I had a 1G a few years ago, I broke a rear axle on the street with only a MBC, filter, 3" turbo back, and centerforce clutch. It's all about how you launch the car.

5. Just like someone said, be prepared for that car to break the bank!!

[Guest]

In response to your reply on #3.

What did you have done to it? What would you recommend?

[Guest]

Troy has a Dogbox = Wayyyy to much money!!

[bluejays]

mwc1 wrote:
Troy has a Dogbox = Wayyyy to much money!!

but its about as bulletproof as you get also.