Welcome sickest honda builder of our time

[CRXASSASIN420]

I actually work at fargo lamborghini...... Tope tier killler master tech is my job title

[ruthless351]

So is he a tech or a lube tech?

[Trafik Jamz]

CRXASSASIN420;296379 wrote:
I actually work at fargo lamborghini...... Tope tier killler master tech is my job title

Sorry, we only buy Ferrari's on this site.

[Rexwagon]

welcome honda humper

[SPANISH-RICE]

ruthless351;296383 wrote:
so is he a tech or a lube tech?

service manager

[bubba]

weshole;296309 wrote:
I know for a fact that a local machine shop in Fergus Falls sleeves blocks and does so successfully. If you want to drive that far, I'll give you the info.

really... i knew they did basic engine work... but they'll sleeve import motors too? and do a good job at it??

ps. this thread makes me lol

[99civic]

dam i get my shit done at elitehonda man shit civic is super fast! i smoke evos and subies all day long man runna like 320 whp 500 on a mustang dyno N/A.... look for my car back window says "FUCK U TRICK" peace bitches im out!

[Bryce]

99civic;296424 wrote:
dam i get my shit done at elitehonda man shit civic is super fast! i smoke evos and subies all day long man runna like 320 whp 500 on a mustang dyno N/A.... look for my car back window says "FUCK U TRICK" peace bitches im out!

And this was AJ's real intro

[DelSlow]

Forgot to throw in $7,000 motor.

[weshole]

bubba;296415 wrote:
really... i knew they did basic engine work... but they'll sleeve import motors too? and do a good job at it??

ps. this thread makes me lol

Tell him what you want done and it will get done. Its not rocket science bro. Theres no voodoo trickery slight of hand to sleeving a block. If you know what you are doing, your golden. Same goes for o-ringing a block.

[DelSlow]

That's not necessarily all true...find me a shop around here that will work on a H22.

[Bassplayer]

DelSlow;296452 wrote:
That's not necessarily all true...find me a shop around here that will work on a H22.

Why would you want to put money into an H22?

[DelSlow]

Bassplayer;296455 wrote:
Why would you want to put money into an H22?

A) I don't, just recall a friend of mine trying to get some work done on one and no one will touch them and B) Why not? What's bad about them?*

*everyone else, let him answer.

[ihaveaids]

The trans?

[bubba]

weshole;296449 wrote:
Tell him what you want done and it will get done. Its not rocket science bro. Theres no voodoo trickery slight of hand to sleeving a block. If you know what you are doing, your golden. Same goes for o-ringing a block.

damn, i'll keep that in mind

Bassplayer;296455 wrote:
Why would you want to put money into an H22?

this

DelSlow;296457 wrote:
A) I don't, just recall a friend of mine trying to get some work done on one and no one will touch them and B) Why not? What's bad about them?*

*everyone else, let him answer.

I think i might know this one....

[Bassplayer]

DelSlow;296457 wrote:
A) I don't, just recall a friend of mine trying to get some work done on one and no one will touch them and B) Why not? What's bad about them?*

*everyone else, let him answer.

H22 are heavier(only slightly), aftermarket support is waaayyy less and so parts are more expensive, H's tend to be harder to swap depending on the chassis, why have barely any of the respectable honda tuning companies put H22's in their race cars..... I guess the list goes on, I've just never really been a fan. I'm a big supporter of keeping things simple and cheap.

[bubba]

Bassplayer;296475 wrote:
H22 are heavier(only slightly), aftermarket support is waaayyy less and so parts are more expensive, H's tend to be harder to swap depending on the chassis, why have barely any of the respectable honda tuning companies put H22's in their race cars..... I guess the list goes on, I've just never really been a fan. I'm a big supporter of keeping things simple and cheap.

i think ur wayyy off from what he was thinking still...

I'm thinking he's referring to the use of FRM cylinder walls from the factory...

[ihaveaids]

bubba;296478 wrote:
i think ur wayyy off from what he was thinking still...

I'm thinking he's referring to the use of FRM cylinder walls from the factory...

Ah thats right, aren't those really weak from the factory and require special sleeves or something?

[inspector01]

ihaveaids;296479 wrote:
Ah thats right, aren't those really weak from the factory and require special sleeves or something?

Well the fact that you can't run aftermarket pistons with them is a bit of a downfall. They are reasonably strong stock, but if you want to run forged internals, you need to resleeve it.

They are a decent motor because they are pretty cheap, and can make decent power, but Im not a supporter either.

And Wes, Sleeves actually do require a very good machinist that knows what they are doing and has a lot of experience (not that it is impossibly hard, but it is a LOT more than boring a block, milling a head, or even o-ringing). I have seen blocks from the big name companies that have had serious issues, fortunately these have pretty much all been figured out over the years, or those companies are no longer around, but I would definately not trust my block to just any machine shop that says they can do it, much better off sending it to a company that does it every day.

[Bassplayer]

inspector01;296482 wrote:
I have seen blocks from the big name companies that have had serious issues, fortunately these have pretty much all been figured out over the years, or those companies are no longer around, but I would definately not trust my block to just any machine shop that says they can do it, much better off sending it to a company that does it every day.

QFT. As soon as you start the motor up and get some boost on it if anything blows up no motor shop around here is going to take liability for it. Get it done at a place that is known for their sleeving and can back up their work. /thead