New Project: 1991 S10
-
350 Small Block Chevy
700r4 transmission
B+M ratchet shifter
Edelbrock Carb
Edelbrock intake manifold
...Holley Red Fuel Pump
Lowered
Dual exhaust
Tint
B+M converter lockup kit
Spray in liner
1999 S10 bench seats
Complete repaint 3 years ago, all new metal everywhere
American Racing rims with BF Goodrich tiresPicked it up for $2900, body is MINT. New doors, new box, new rockers, any rust was cut out and replaced with new metal. Stock 350 but pulls pretty good.










-
zbrown;320294 wrote:
Clean! I like itMe too, eventually I'd like to go lq4/4l60e or Ls1 and just beef up the 700r4 that's in it a bit. For now though it will get some minor things and I'll just drive it through the summer and enjoy it since I just got it.
-
Looks clean!
Word of warning, its either the Holley blue or red pumps that spontaniously combust on occasion and usually fail randomly. One is decent, the other one is garbage. It escapes me to what one is which though. Im too lazy to look for the thread that talked about it somewhere...
Got the same steering wheel as my Cutlass too! :icon_cheers:
-
HandoEX;320308 wrote:
Sweet! What does that thing weigh?Anywhere from 2600-2800 is curb weight. This thing is tiny and similar trucks are at about 2650-2700 lbs.
And the 350 will be in it for awhile but It's just not what I want. I found a 4l80e LQ4 pullout for $850 I may jump on and stick in a corner until I'm ready for it.
A few people have told me to stick with the carb'd 350 setup but I just don't like it, not my cup of tea so I will EVENTUALLY get rid of it. I may do some minor things to wake it up like swapping out the 3.08 gears, getting a locker for the rear, a proper dyno tune etc for the time being.
-
New seats and steering wheel.
Steering wheel is a Grant, seats and console are from a 91 Bravada and are buckets instead of the 60/40 split that was in it.
NEW

OLD

NEW

OLD

-
Posted the wrong pic for the last one, and it won't let me edit the post.
Here's the correct OLD pic:

-
I've gotta agree with the crowd here the 350 has one helluva lot of potential, like 600+hp for around $3000 in parts potential. You can always vortec swap if you want efi, or god knows there is just a little aftermarket support for standalone efi systems, but I'd leave that powerplant in place. Bottom line is the sky's the limit with what you have and in the end the 350 parts will be cheaper, especially since you could get a lot of stuff used.
-
Looks pretty sweet.
I think a blacked out grill and a roll pan would make some nice added touches as well.
-
I actually like the gauge as is, but the rear bumper and receiver will be removed.
I plan to replace the rear with a bumper from an s10 blazer, looks like this:

-
I actually like the gauge as is, but the rear bumper and receiver will be removed.
I plan to replace the rear with a bumper from an s10 blazer, looks like this:

-
Something is seriously wrong with this forum. I can't edit posts and it double posted...
anyway that was supposed to say Grill** and have a pic of a blazer bumper, like this:

-
Something is seriously wrong with this forum. I can't edit posts and it double posted...
anyway that was supposed to say Grill** and have a pic of a blazer bumper, like this:

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


