F*** all
-
so i just spent the last........fuckin........god...............hour plus trying to install my goddamn BBK intake that came in today. Motherfucker if i only woulda known that was a 2 person job. Piece of shit i cant take the car to school tomorrow because im ready to blow the whole goddamn thing up. Stupid rubber pieces that are supposed to hold the oxygen sensor and hold the fenderwell and bottom intake piece so there is no ratteling keep on falling through so i have to take the whole goddamn intake assembly apart again, get the fuckin rubber piece out, and retry again and now i just wanna kill something. Fuckin filter wont fit snugly over the damn piping and i cant fit my arm up around through the fender to get it on snugly ...... yes this venting feels sorta good right now. So yeah thats my story, im a complete fucking idiot, i cant install intake for shit, i hate everything and everyone, mustangs suck, fuck cars.
side note: my first official "performance" mod was started on today, BBK short-ram cold air intake, whopee
[/vent]
-
shitty, hope it works better for ya soon
-
lol....you'll learn!!! keep trying buddy!
-
So much hatred in this world.......
-
take a deep breath and drink some beer LOL
-
I feel for ya man, I just pulled my engine yesterday and it took me damn near half an hour to pull the bumper off, 4 bolts for it were stuck and inacceable. I so wanted to just tourch it and call it a crazy mod.
-
it will be ok, it will be all good in the end.
-
It's kinda like when you install your first cd player and something doesn't work so you pull the dash apart 3,4 or 5 times then finally realize, that you just blew a damn fuse.
The satisfaction of doing it and finally getting it done and knowing you did it yourself will greatly outweigh all the bullshit you went through to put it in.
Sterling Archer: Oh my god! You killed a hooker!
Cyril Figgis: Call girl!
Sterling Archer: No Cyril! When they're dead they're just hookers!
-
^that is very true!
-
you know, you remind me of "lil brudder" from www.homestarrunner.com , no matter how hard he tries, he just doesn't give up......keep on going lil brudder, keep on trottin!!
-
Don't worry all that hp that you will gain with the intake will make it worth it.
I installed an intake on a 99 V6 Stang a few years back and that only took maybe 1/2 hour. I am not sure why it would take so long for your car.
-
its in now. lol i saw it today and it looks pimp. the car died though when
-
Ok so me and my mom put it in this morning, finally. Amazing how much easier it was with a 2nd person. After we finally got the piping fit in and through the rubber thing that kept popping out on the fenderwell mount, it went like a breeze (prettymuch). Got everything reattached and it worked, there is a little bit of a difference, not much, but i wasnt expecting to drop 4 seconds or anything. Then when me and kenn were gunna go to BK today i started it up, it was idling REALLY bad, then died. Popped the hood and one of the hoses had come off from the piping so we went to wally world and bought some hose clamps and it works fine now, there might be a small air leak somewhere but i'll get that checked out when i care. My check engine light has also been on for awhile and we used our scanner and it said "mixture too lean" so some advice would be to disconnect battery, let the computer die, and then start it up and let it recalcuate everything? or what should i do. At least its on now, thanks for the ... non flamish replys to my venting
-
StangerBanger96 wrote:
My check engine light has also been on for awhile and we used our scanner and it said "mixture too lean" so some advice would be to disconnect battery, let the computer die, and then start it up and let it recalcuate everything? or what should i do.I would start by doing what you said... and see if the computer can calculate the air/fuel mixture correctly again. If it still comes back after you reset the computer... it might be time to replace your O2 sensors. Another think to check is your mass air sensor. Try and clean it off. That can throw everything all to hell too. Good luck.
-
Stupid rubber pieces that are supposed to hold the oxygen sensor
I'll assume you're meaning ACT sensor?but yeah, check for leaks, unhook the battery (or pull the EEC fuse in the fuse-block under the hood...however on a mustang/3.8L I couldn't tell you which one it is)...
Make sure your MAF and ACT sensor is plugged in (should be a breather or two as well, make sure those are secure and there aren't any holes/bungs unused/open).How is the MAF positioned with the tube? It's been argued that a bend directly before the MAF causes an inaccurate reading (airflow isn't uniform across the diameter of the MAF).
and like 5.0 said, clean the MAF. Q-tip and rubbing alcohol IIRC.
And it's an Intake Tube... the Intake bolts on to the heads, then the plenum, and throttle body, and then the intake tube. (just a little pet peeve I've got)
-
So here is the visual explanation now....
in the first picture, the yellow circled areas were the things that made the install hell. The stupid strut support is right in the way and allows NO room to work with after the piping is under it. Then the stupid sensor i circled (dont know which one it is, 02?) didnt fit in the hole so they supplied the stupid little rubber piece to make it sit in place, but that was the piece that kept on popping right through and falling into the piping, requiring me to take the whole piping apart again. Then that last clamp was a problem lastnight and a breeze this morning just because there was about..ohhhh.....2mm between the 2 pipes when the lower pipe was all the way into the fender and the upper one was on the TB. Then when i got this all in and working today, the part that disconnected was the pipe leading from right above the BBK emblem to the plenum, so i just put that pipe fastner over it and hopefully everything holds.
Then we move on to image 2. The hole in the fenderwell where the piping slides through had the same thing the 02 sensor had, where whenever i would try slide the piping through the rubber part would bend, fold, and pop through the hole and down into my damn fender.
And yes i have a very dirty engine bay
-
ticklemedaly wrote:
you know, you remind me of "lil brudder" from www.homestarrunner.com , no matter how hard he tries, he just doesn't give up......keep on going lil brudder, keep on trottin!!
"that little guy, he's got the heart of a champion"
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login