missing cam

[zbrown]

I think cams in general are bogus.....

[94_dsm_nt]

inspector01;185500 wrote:
Is it just me or does your header look f-d up??

That's Ford's design, cause the factory manifolds/headers on my Mustang look pretty much the same.

[MisterCMK]

Yup, they have that little pinch in them.

I have both heads off and the pistons/block surface cleaned up and ready for the heads. I am working on tapping the block holes and will probably bolt the heads on tonight. Fucking autozone shit taps breaking off blow ass BTW

[Parker]

zbrown;185554 wrote:
I think cams in general are bogus.....
ITS A BIG GOVERNMENT CONSPIRACY!!!

[Guest]

Parker;185576 wrote:
ITS A BIG GOVERNMENT CONSPIRACY!!!

Damn liberal hippies and your crazy conspiracy theories!!!

[MisterCMK]

[MisterCMK]

And the tap that almost fucked me

[thrash]

Wow that tap is nasty. How did that happen? Were you using oil?

Also, what's that a mechanical distributor doing there? I thought I was kidding about 1930

[MisterCMK]

Haha, it is a PIP sensor in there, so its only 1950s tech.

Anywho, it was just a shitty tap. I wasn't using oil, but it was not getting tough at all and then just snapped. That is what I get for being lazy and not wanting to drive all the way down to Sears to get a good tap. I ended up going down there anyway.

[XJHEAD]

I remember when my engine-bay looked like that.

[SPANISH-RICE]

whatd you do to clean the tops of the pistons while they were still in the motor? worried about anything being between the cylinder and pistons? an earlier pic looked like there was quite a bit of carbon build up

[MisterCMK]

Yeah, there was quite a bit of carbon buildup. I used a wire wheel cup that you chuck up in the drill. I brought each piston to the top and cleaned it off and also cleaned off the block. Then, I took brake cleaner and sprayed down the cylinder and rotated the engine until I didn't see any crap left behind in the cylinders. I know that there is going to be some crap left over, but I am going to change my oil right away after I start it up to get some of the stuff cleaned out of there.

I have both heads on and torqued and the valvetrain re-assembled. Now I have to finish cleaning up the valve covers and then put the intake manifold back on and put 'er back together. I have more pics that I will put up soon.

[MisterCMK]

Still have polishing left to do on the valve covers.

[thrash]

this is the 4.6 engine right? is it 100% metric hardware now ?

[XJHEAD]

thrash;185729 wrote:
this is the 4.6 engine right? is it 100% metric hardware now ?

4.6 not until 96'
about 1/3 of the 302 shit is metric, pain in the ass

[MisterCMK]

The motor is almost all standard but then the body is metric. Fucking clusterfuck. haha

[Ngige]

MisterCMK;185561 wrote:
Yup, they have that little pinch in them.

I have both heads off and the pistons/block surface cleaned up and ready for the heads. I am working on tapping the block holes and will probably bolt the heads on tonight. Fucking autozone shit taps breaking off blow ass BTW

i hope you are not runing a tap:nonono: , you need to use a thread chaser all you are doing is cleaning your threads on the block, you may not see it but taps take a little amount of material off, and thets going to fuck with your torque numbers on your head bolts or studs.

[MisterCMK]

eh, its done already. Oh well. Good to know for next time.

[XJHEAD]

Actually what you want to use is a bottoming tap. It does not have the taper to it. The thread sizes are the same. It will let you reach the bottom of the hole.
Ngige is correct when he said it does affect torque values as you still have material at the bottom of the threads.

[StangerBanger96]

thrash;185729 wrote:
this is the 4.6 engine right? is it 100% metric hardware now ?

5.0 = Pushrod
4.6 = OHC

5.0 = Easy to work on and fairly small dimensionally...note the room to work with in his engine bay
4.6 = Bitch to work on and picky as hell with mods, also larger than many big block engines.

His Engine (5.0)

My Engine (4.6)