Fargostreet.com

Most likely a wheel speed sensor is either bad or the connection is corroded. You can try to clean the connections and see if that goes away or take it to someone who has a Tech 2 scanner to pull what sensors are defective.

Sounds good. I may put it in tomorrow out at my bro's in Enderlin, then test it out on the drive back on monday. Oh yeah, the guys over on my Bonnie site said that I probably wouldn't need it, but it would help to get it done anyways just to make everything match up perfectly.

Does anyone know where would be the best and/or cheapest place to go to get a Crankshaft Variation (CASE Learn) on my car once I put my new PCM in? Does anyone have a tuner that could do this? I know I can go to a dealer and get it done but dont want them to charge me possibly $100 to do it. I also do not want them to re-flash my PCM back to original specs and lose my programming. I haven't called any dealers to see what they would charge so I'm not sure what it may run me.

People mod these cars because they want to. I want to add some power to my SSEi because I want to, simple as that. You can drive cirles around me if you want, I'll be happy in my shitty handling boat...
www.bonnevilleclub.com
www.intense-racing.com
www.zzperformance.com

Domestic power FTW! runs and hides from 95% of this board...

Where's those pics Torby???

Yeah, I found that the SWI-JACK will work for the XG700.

Oh, hey Tom. I like to pretend I know a little about cars...

Hey, dont be hatin on the Bonnies!!!

Can anyone confirm that I need the following modules to keep features in the car...

Metra GMOS-09 for chimes/RAP/etc.
PAC SWI-X for steering wheel controls

PM Sent...

Yes, my name is Luke. Do I know you MS6???

I believe it's the Bose system. Can I just add in an aftermarket amp into the current system?

Anyone have any pros/cons on JVC head units? I've always had Pioneer up until now and liked them. I'd like to put a double-din in my SSEi and would like to keep the dash clean but pioneer doesn't have one that I'd put in the dash.

What all is needed so that I don't lose my chimes and anything related to the factory HU? And I know i'd need another module to keep the steering wheel controls. Here's what I am lookin at.
KW-XG700

http://mobile.jvc.com/product.jsp?modelId=MODL027886&pathId=148&page=1

Here's Pioneer's offering, I'm not so big on the green backlights...
FH-P4200MP

I've been playin TF2 more than CS:S lately. Orange Box ftw! Although I've already beat HL2, Episodes 1 & 2, and portal...

I like the case that I bought this fall when I built mine. It's only a mid-tower so it may be smaller that what you want if you're lookin for a full.

http://www.newegg.com/Product/Product.aspx?Item=N82E16811156063

That all depends on who's askin...

94NDTA;198211 wrote:
Tell him to shut up. Your car would actually be slower if you put a smaller pulley on with no supporting mods at all.
I tell him to shut up all the time so it's all good.

94NDTA;198158 wrote:
Thats GM's high quality chrome rims for ya.

Don't fool yourself, a smaller pulley is going to cost a good amount more than $100 when all is said and done. You will either need to learn how to tune, or pay someone to do it for you, plus you will need mods to support the smaller pulley.

If you have any questions, feel free to pm me.

Yup, the "Swoopies" as they are called on my bonneville forum.

I know that a PCM, rockers, open up the exhaust, etc would eventually be necessary along with the pulley. Bobbles just keeps bugging me to throw on a pulley and be done...