Motor choice
-
out there wrote:
this is totally a "ricer" mentality, the idea that high-revving equates to powerful :rolleyes:
believe it or not, there are many turbo guys on honda-tech that are making peak power below 6k. proof? look at kevin's dyno graph's when he had a stock intake manifold.
how much power he wants to make and how much tuning he wants to go through are the major factors in deciding what kind of turbo he wants. a larger turbo (57trim) will make more power at 10psi than a t25, obviously because it's a larger turbo and pushes more volume.
granted, the big turbo will push much more air (read: is capable of higher engine rpm), but the gears are still so close, so it would only pull for so many rpms. to truly take advantage of a huge turbo, one would want to gear the transmission to engage into the next gear at an rpm that creates enough exhaust pressure to spool the turbo again after shifting; but, then you would lose practical driveability...
yeah, i'm done ramblingcliff notes: how much power does he want and how much tuning is he willing to pay for?
i was just referring to that being the only major difference between the ls and gsr block. in no way did i say you need to rev 13k rpms to make power. that and the b18b is stronger supposedly. ricer? psh
-
so is that better then
Matt
92 Civic HB
JDM d15b w/14b@8psi
-
i would like right around the 300hp range sooner or later. I dont want to have to spend a lot on tuning the thing all the time. I just want it to run good and be quick. i would be satisfied if i hit 13 with it in a year or so. summer of 06 i would prolly just do little miner mods like the intake, full exhuast, plugs, wires fuel stuff, ignition and what not.
Matt
92 Civic HB
JDM d15b w/14b@8psi
-
btleier wrote:
BUT... bottom line is if you want over 300whp........ you'll either need to b-series turbo, or a well built d-series.I completely agree. The fact of the matter is that you can have as many d-series motors as you are willing to pick up out of people's driveways....b-series are still expensive to replace. Blow up a d-series?!?!?....who cares. In a turbo app there isn't many up's to have the b-motor.
-
agreed. however it also depends on the person, if you decide to test the limits of the stock d-series make sure that you are willing to put in the time to swap motors/trannies/clutches... if you're not willing to do that, this may not be the route for you.
-
what i was saying was, simple bolt ons ie: headers, exhaust, cai doesn't increase hp very much on any B, D, H, F series honda engine.
as far as going D or B if he plans on going with around 300 hp. i have this feeling its going to end up costing him more in parts and labor with a D series in the end, because 300 hp is about as much as you can push out of the D and thats built. now if you blow that up you have to buy another have it built and put in again. 300 hp out of a B series is relatively descent power for a B. your not pushing it to its limits so parts breaking isn't quite as much of a problem.
just out of curiosity what has tufte all replaced on his D? and what has gsr all replaced on his B?
-
to make any power with a turbed honda u MUST sleeve the block then it wouldnt matter what motor u went with because u could push 25+ psi and if u want more just go with a bigger turbo..
b16-2000$
sleeves-1000$
supporting mods- lets just say 1000$
huge turbo-1000$
labor and shit- idk ask somebody that knows -
spoolude wrote:
to make any power with a turbed honda u MUST sleeve the block then it wouldnt matter what motor u went with because u could push 25+ psi and if u want more just go with a bigger turbo..b16-2000$
sleeves-1000$
supporting mods- lets just say 1000$
huge turbo-1000$
labor and shit- idk ask somebody that knowsuntrue.... there are a plenty of guys running ridiculous hp numbers on stock sleeves now 400-500whp. go hop on honda-tech and look. they're been using forged internals, but have been keeping the stock sleeves.
-
spoolude wrote:
to make any power with a turbed honda u MUST sleeve the block then it wouldnt matter what motor u went with because u could push 25+ psi and if u want more just go with a bigger turbo..b16-2000$
sleeves-1000$
supporting mods- lets just say 1000$
huge turbo-1000$
labor and shit- idk ask somebody that knows
Damn it Spoolude, we should ban you from "Car Tech"... -
im thinking the b18c1 is sounding good. Are they quick stock?
Matt
92 Civic HB
JDM d15b w/14b@8psi
:rolleyes: 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login